How to Install a Ghost Immobiliser
Ghost immobilisers are hidden security system that shields your vehicle from key cloning and hacking. It works by stopping the engine of your vehicle from starting unless it is started using a PIN code that can be up to 20 characters in length.
It is not detected by thieves, who are unlikely to think about this additional layer of security. Certain systems come with an app that allows the owner to deactivate their immobiliser if they forget their PIN number or use the service/valet mode.
Connecting the vehicle's CAN Bus to the vehicle's
The Ghost 2 Immobiliser is an advanced security system that can be integrated into your vehicle's ECU and provides a discrete protection against thieves. It is highly efficient and user-friendly. This makes it a valuable asset to your vehicle's security arsenal. However, like any anti-theft device, it is not impervious to failure and requires regular maintenance to ensure its operation. This guide will help you make the most of your Ghost 2 immobiliser.
CAN (Controller Area Network), a robust serial networking system that lets microcontrollers communicate with each over short distances. A central control unit is not required. It is designed to multiplex electrical wiring in vehicles, saving on copper. It has many advantages, including low cost and easy use.
In most modern cars in modern vehicles, the CAN protocol is used to connect with a variety of systems, including the engine management system (EMS), transmission controller, steering module air conditioning controls, and more. It also transmits sensor data like speed sensors and other inputs, to control the car's various features. The CAN bus is used to monitor these diverse components, and it can stop the car from starting if they're in a dangerous state.
While the CAN bus can be employed for a variety purposes, it's crucial to know how it functions and how it's secured. It's possible to add new features to vehicles using CAN bus, however it's crucial to safeguard it from threats from hackers and other types. Installing a firewall and monitoring your CAN bus with software is the best method to accomplish this.
Ghost2's control device is hidden in the dashboard or wiring harness, which prevents an intruder from physically altering it. It is impossible to reset a PIN or emergency code without access to the car.
If you have to give your car away for servicing, valet parking, or any other reason, you can activate the Transport Mode. This feature will disable both the keyfob as well as the ignition functions of the Ghost immobiliser. It will only be activated after the car has reached 31 mph over a period of 15 minutes.
Creating PIN codes
The Ghost immobiliser is a robust security device that shields your vehicle from thieves. The patented technology makes use of the PIN to disable the vehicle's engine and prevent it from starting if you don't have the correct code, or an authorized fob or mobile. The system's subtle design is unnoticeable and offers unrivaled protection against theft. Moreover, the system is TASSA verified and can lead to significant savings on car insurance premiums.
During the installation, Ghost enters a "learning mode" to record the sequence of buttons pressed in order to create unique pin codes. The installer will guide you through activating the system once the pin code has been created. Once activated, the Ghost system shuts down the motor that starts your vehicle unless you enter a valid pin or switch the vehicle into transport mode. This makes it extremely difficult for thieves to copy or hack your vehicle's starter system.
Installing an Ghost immobiliser is straightforward however it is essential to follow the specific instructions in the user guide to ensure proper operation. Basic hand tools can assist in making the perfect connections and a multimeter can aid in checking the electrical value. Insulation tape, heat shrink tubing, and cable ties can be used to shield exposed wiring. Also, make sure to test the system on a regular basis to find any problems and potential mistakes.
It is important to check the system one final time prior to turning on the ignition. Ghost immobilisers will re-arm themselves after 3 to 30 seconds dependent on the model of your vehicle. The system also comes with a Service/Valet Mode that lets you temporarily disable the system for servicing or valet parking.
Ideally, the immobiliser should be concealed in a hidden location beneath the steering wheel or dashboard. Use a small amount of duct tape or paint on the CAN H and L wires to make them easier to locate when testing. The CAN H and the L wires should also be connected to an electrical source that can provide a constant 12V. It is also crucial to check the connections following testing, as misidentifying these wires can cause the system to fail.
The system must be activated
A ghost immobiliser stops your vehicle from starting unless you press a set of buttons inside the vehicle, usually the steering wheel, door panel, or central console. The sequence can be changed by the user in case it is needed. Once activated, the system can't be removed. This makes it a great choice for anyone looking to protect their vehicle from theft.
The system is designed to be undetectable, which means it cannot be detected by modern diagnostic tools or code-grabbing technology. It does not emit radio frequency either making it even more difficult for thieves to find.
If the device is found, it will stop the engine from running. It will also sound an alarm to scare the thief away. The device can be used to track the location of a car, which will aid in the search for the vehicle in case it has been stolen.
If you're interested in a ghost-immobiliser call the experts at Car Specalist Customs to get a quote and discuss your options. We are able to install ghost immobilisers in your vehicle. We will make sure that it is hidden in a location that is difficult to reach. We can also provide additional security measures, such as the wheel lock and kill switch to help protect your vehicle from thieves.
Disarming the system
If you have an Ghost immobiliser fitted to your vehicle, it's important to know how you can disable it. This will aid you in the event that you lock your keys inside the car or if your battery goes out of. The system utilizes a unique PIN code that only you know, so the immobiliser will not be able to start your vehicle unless you enter this code. Pressing the combination buttons on the steering wheel or on the dashboard is the most efficient way to enter your code. This is much simpler than using a key fob. It also prevents others from copying the remote.
Unlike some aftermarket immobilisers that require cutting wires for installation, Ghost2 is non-invasive and is compatible with your vehicle's bus network to function. Its standout characteristic is its ability to bypass the engine without affecting the normal functions, making it difficult for thieves to make use of signal boosters or clone your car key. It does not emit radio frequencies, which means thieves won't be able to detect it.
The Ghost system comes with a Transport Mode that allows you to temporarily disable security for certain situations such as transportation or service. This is a great option when you have to lend your vehicle to someone without sharing the PIN code, or if you want to ensure your vehicle is secure while driving it. Press the service button five times over two seconds to enable Transport Mode. The Ghost system will confirm activation via five indication signals.
Save the emergency code outside your vehicle in a secure location. If you ever find yourself locked out of your car you can contact the technician or company who installed the system, and they'll give you the code. If you cannot reach them, you can always try to contact an authorized dealer however this will require verification procedures and could result in additional fees.
Apart from the ease of this system, you can rely on it to protect your car against theft and help reduce the cost of insurance. Many insurance companies offer reduced monthly premiums or even financial incentives to install this anti-theft technology.